IOT has been all around us for quite some time now and it has almost revolutionized the way machines communicate among themselves.As a starting point here is a simple project tutorial on creating Arduino web server that will help you to open the doors to IOT.In this tutorial we are going to host a simple web server as shown in the above image.

Remember you can host a webpage in your ESP8266 but the controlling functionality is pretty less in it.Given that there are only two GPIO pins in it.Also it doesn't have of PWM, timer and other options.ESP866 serves as a communicating medium which enables Arduino to join a LAN.We can use our WiFi enabled mobile phones/ laptops to form a LAN with Arduino.From our devices we will access the Arduino web server, fetch the webpage from it and control the modules or components connected to it.I have made avideo explaining this entire tutorial – please do check that out

COMPONENTS REQUIRED:

1. Arduino Uno
2. ESP8266 WiFi module
3. LEDs
4. Connecting wires
5. Birdirectional Logic converter
6. Mobile or Laptop or other WiFi enabled devices

QUICK BRIEF ABOUT ESP8266:

I presume most of us are familiar about ESP8266 chip.188bet服务官网For those who are not aware of it, ESP8266 is a versatile low cost WiFi chip that is capable of providing WiFi connectivity to your embedded projects.188bet服务官网It can work in both Station and AP mode which makes it a perfect choice for IOT projects.Apart from this it also has two GPIO pins which can do some basic turning ON/OFF.

USAGE IN CREATING ARDUINO WEB SERVER:

In this project the whole purpose of ESP8266 is to provide a WiFi link between Arduino and our mobile device.We are creating a Local Area Network (LAN) by using ESP8266 as Station and connect it to Mobile/ Laptop (WiFi enabled devices) which serves as AP/Hotspot.Any devices connected to this AP will be within this LAN ( i.e ESP8266 + Arduino and Mobile devices ).Therefore they can communicate with each other and access the Arduino web server.In order to do all this we should program Arduino to feed a specific set of AT commands to ESP8266.

AT COMMANDS:

Predefined AT commands will decide all the parameters of WiFi link in ESP module.Using this we can control the way ESP8266 make or release the connection with other WiFi devices.This includes Setting AP password, Joining AP's, Creating server and so on.  Refer this link for "Complete AT command list" used in ESP8266

ESP8266 RESPONSE:

In return to the input AT commands, ESP8266 will acknowledge with response codes which indicate whether the input AT command was accepted or declined by the device.This whole command input and response will be transmitted via Serial communication /UART.

To keep this simple, for majority of commands ESP8266 will respond with given Input command followed by the characters "OK\r\n".For example if we send the command AT then the ESP response will be

AT\r\n
\r\n
OK\r\n

This is common response for most of the commands.There are also other response codes that we would need to monitor for this project, which will be discussed later in this article.

ERROR DETECTION AND RECOVERY:

ESP8266 modules can be very buggy and it can be very prone to errors while working with Super fast Arduino.Considering this we need to write the code in such a way that Arduino can detect error response from ESP modules.In order to do that we need to check for appropriate response from ESP module for every Input command.

SCHEMATIC DIAGRAM:

From the above schematic diagram, you can see that Arduino is connected to a Bidirectional Logic converter LG1 which basically converts the logic from 5v to 3.3v and vice versa.This is to help both Arduino and ESP module to identify the logic 0 and 1 in order to communicate with each other via UART.Apart from that the schematic diagram is pretty straight forward.The headers in the Plug-in board section is for providing easier connectivity for ESP8266 when using it with Arduino or any other developmental boards.

TESTING YOUR ESP8266:

I strongly recommend this step since ESP8266 can be buggy and it's quite necessary to have this tested.Upload the bare minimum code to the Arduino and connect the ESP8266 as shown in the schematic.Once done use the following commands, but remember to select "Both NL & CR" & Baud rate as 56700 which is default baud rate used by ESP module.

AT – OK
AT+RST
AT+CWMODE=3
AT+CWJAP="SSID","Password"

The above command will make your ESP8266 to join the network you wish and it will remember the AP even after powered down.This is important in terms of this project because the code is developed in an assumption that ESP8266 was already connected to AP or hot spot of mobile device which we will use.This is because connecting to AP through the code seems to make things complex with no considerable benefits to this project.

AT+CIOBAUD=9600

This command is to alter the baud rate at which the ESP module operate.I had to do this since ESP modules worked better with this baud rate than higher speed.

PROJECT WORKING:

Arduino web server can be accessed by the devices within that LAN to control the LED's or other components.ESP8266 will remember the AP's that it has been connected to previously.It will get connected to AP as soon as hotspot in your device is turned ON.Once connected, a LAN will be created.Once Arduino detects a connection via ESP8266, it will start sending commands to ESP module to create a server.I have added a LED to indicate server creation.Mostly it will take about two seconds from the moment ESP is connected to WiFi AP.

Once the Arduino web server is ready, open any browser in the devices connected to the LAN and access the IP address assigned to ESP8266 module.Arduino will send a piece of HTML code to the client via ESP module and a webpage will be displayed on your device browser.HTML codes from the Arduino were built to display button in the webpage.Using these buttons user can feed input back to Arduino.Based on the received inputs, Arduino will activate/deactivate LED's or any other devices that are connected to it.

ESP COMMANDS USED FOR CREATING ARDUINO WEB SERVER:

These are the list of commands that we are going to use to create this Arduino web server.

"AT+RST" – Reset the ESP8266 module
"AT" – Response check
"AT+CIPMODE=3" – Set the module as both Station and AP
"AT+CIPMUX=1" – Setting to allow multiple connections
"AT+CIPSTA= " – Assign any local IP address but make sure it is compatible with your device.
"AT+CIPSERVER=1,80" – Creating server with port 80
"AT+CIPSEND= ,

CHOOSING IP ADDRESS:

I manually set a static IP to my ESP8266 module even though my mobile DHCP will assign IP when connecting with it.I am doing this to make sure I know the IP address of ESP device and I can connect to it without any problem.Without doing this DHCP in my mobile phone will assign IP address which is currently free and you will not know this while using this.But you should take care when choosing your IP address since local IP address differs from device to device.I have read in a documentation that Android phones are programmed to use 192.168.x.x to assign for the devices connecting with it locally.So I have used the IP 192.168.43.253 to assign for ESP module.So search in internet for the IP your devices will use and add it in the code.

HTML WEBPAGE:

So now the server is created in ESP8266.When I am saying server is created, it means that ESP8266 is ready to take client request (that is the browser).Remember ESP module serves only as a communicating medium here, so it's the Arduino here that respond with the HTML webpage  when a client request is detected.

Welcome to Arduino LED control Wizard
You can turn ON/OFF LED connected to Arduino using the buttons given below
TURN ONON
TURN OFFOFF

ALGORITHM:

1. Input "AT+RST" command and wait until ESP8266 connects with AP.
2. Check for "IP\r\n" in the last four characters of ESP response, this indicate that WiFi got IP.
3. Once connected start feeding the commands to activate the server mode in ESP8266
4. Monitor the response for each input commands.
5. Proceed with the next command once the last four characters of response is "OK\r\n" throughout the Server sequence commands.
6. Force Arduino to wait for the client request from any browser connected within the LAN.
7. Once request is received check for connection ID provided by ESP8266 and add it to the command "AT+CIPSEND"
8. Check for the character ‘>' in the response string from EP module.
9. In case of incorrect response repeat step 7.
10. Once correct response is verified send the webpage HTML code from Arduino through the ESP module to client browser.
11. Wait until you receive response from ESP8266 module and check for the last four characters "OK\r\n" in the response string.Webpage should have been successfully displayed in the browser now.
12. Force Arduino to monitor the incoming GET request from Client (button press)
13. Once client GET request is received check for URL parameters in the request, for example GET: /ON , in which /ON is the URL parameter.
14. Activate/ Deactivate LED/ other devices or do something based on the URL parameter in the response.

WORKING VIDEO:

CODE:

/*Simple code to create webserver in Arduino and control things within the network   Created by Frank Donald */  char Input_buffer[550]!boolean command_flag=false!int i,j!boolean stringComplete=false!boolean request_processed=false!boolean WiFiConnect=false!short int command_count=0!char send_bytes[]="AT+CIPSEND= ,379\r\n"!boolean client_request=false!boolean flag=true!char connection_id!short int page_input_pos!void setup() {    pinMode(13, OUTPUT)!pinMode(12, OUTPUT)!digitalWrite(13,LOW)!digitalWrite(12,LOW)!Serial.begin(9600)!delay(5000)!Serial.print("AT+RST\r\n")!delay(200)!while(WiFiConnect==false)                             //Wait till Connecting to WiFi hotspot    {      serial_check()!WiFiCheck()!//WiFi check subroutine    }        while(command_flag==false)                           //Looping for commands     {      command_input()!}    clear_buffer()!//Clearing the array    while(client_request==false) //Waitingfor anyclient/browser to initiate the request    {      serial_check()!brow_req()!//sub routine to check browser request      brow_resp()!//sub routine for response from Arduino    }    flag=false!}    void loop() {    serial_check()!page_input_pos=Search_webrequest()!//Monitor webpage indefinitely    activate()!}      void activate()  {    if(flag==true)    {      if(Input_buffer[page_input_pos]=='O'&&Input_buffer[page_input_pos+1]=='N')      digitalWrite(12,HIGH)!else if(Input_buffer[page_input_pos]=='O'&&Input_buffer[page_input_pos+1]=='F')      digitalWrite(12,LOW)!}  }    void WiFiCheck()                                        //Check whether WiFi is connected   {    if(stringComplete==true&&Input_buffer[j-4]=='I')   //Check for the status WIFI GOT IP     {     clear_buffer()!WiFiConnect=true!delay(500)!}    else    {      clear_buffer()!stringComplete=false!}  }    int Search_webrequest()                                   //repeated loop to check button inputs from Webpage  {    if(stringComplete==true)    {      for(i=0;i
         
          ')                              //Checking for the Send data signal from ESP  module      {        memset(Input_buffer,'\0', sizeof(Input_buffer))!Serial.print("
          
Welcome to Arduino LED control Wizard
          
You can turn ON/OFF LED connected to Arduino using the buttons given below
          
TURN ONON

          
TURN OFFOFF
")!delay(2000)!serial_check()!//while(command_response_check==false)!clear_buffer()!request_processed=false!client_request=true!}      else      {        clear_buffer()!request_processed=false!//If request response didnt turn out successful mark the flags so that another CIPSEND command can be passed        flag=false!}    }  }    void command_input()                                      //Sub routine for commands to create server using ESP module  {    serial_check()!if(command_response_check(Input_buffer)==true) //Checking the response and Tracking the counts of command to handle in case of error response from ESP    {command_count=command_count+1;}    else     delay(1000)!clear_buffer()!switch(command_count)                                  //Enter commands sequentially in creating server    {      case 0: { Serial.print("AT\r\n")!delay(500)!break!}      case 1: {                 Serial.print("AT+CWMODE=3\r\n")!delay(1000)!break;}         case 2: {                Serial.print("AT+CIPSTA=\"192.168.43.253\"\r\n")!delay(1000)!break!}      case 3: {                Serial.print("AT+CIPMUX=1\r\n")!delay(1000)!break!}      case 4: {                Serial.print("AT+CIPSERVER=1,80\r\n")!delay(1000)!break!}      case 5: {               command_flag=true!digitalWrite(13,HIGH)!break!}    }  }    void clear_buffer()                                             //Clearing buffer  {    memset(Input_buffer, '\0', sizeof(Input_buffer))!stringComplete=false!}    boolean command_response_check(char *a)                         //Checking for OK Response from ESP  {    if(a[j-4]=='O'&&a[j-3]=='K'&&a[j-2]=='\r'&&a[j-1]=='\n')    return true!else    { delay(1000)!return false!}    }    void serial_check() {                                           //Serial char available check    i=0!while (Serial.available()) {      delay(2)!char inChar = Serial.read()!Input_buffer[i]=(char)inChar!i=i+1!stringComplete = true!j=i!}         }
         

NOTE:

1. The above code can only handle request from one client only, so you cannot use more than one client at a time , also ESP module is capable of handling 4 connections at time which leaves us with 2 client limitations all the time.
2. LED is here for just an indication you can do some cool stuffs like PWM, Timer, Data receiving and so but of course with tweaks in the code but concept remains the same.