In Wireless communication binary data or bits was transmitted by means of a wireless modem (Modulator and Demodulator) which uses FSK technique to transmit bits from the modulator and the demodulator.In FSK technique the carrier frequency is shifted between two preset frequencies since the carrier frequency is shifted between two preset frequencies it was named as Frequency Shift Keying.Today we are about to see designing of simple design of wireless modems using IC NE555 and PLL 565 which uses the FSK signalling technique.It was really a worthy mini project to do for the Electronics students and even it was given in Anna university Electronics Design Lab syllabus for ECE (Electronics and Communication Engineering) students.There are three main basic components in a wireless modem they are
Modulator
Communication link
Demodulator
FSK MODULATOR:
The above above circuit was the Modulator part of our wireless modem.Here IC 555 was wired as a Astable Multivibrator in addition to a transistor through which the data bits are fed into the circuit.The working of this circuit was very simple to understand as the output frequency of the signal was based on the digital input given to the base of the transistor.
When the input data was logic 1 PNP transistor Q is off and this makes IC 555 to work in normal astable mode giving out series of square wave pulses and thus there will be no change in frequency of the output signal.But when the logic 0 was given as input then the PNP transistor is on and it connects the resistance Rc across Resistance Ra.This makes the charging of capacitor C quicker resulting in high frequency waves as output by this way the FSK was done with this circuit.The output frequency of this circuit will be 1070 Hz or 1270 Hz.For detailed description of this circuit visitFrequency Shift Keying using 555.
RC FILTER:
The output obtained from the Modulator will be of square wave so in order to convert the square wave use a low pass filter shown in the above circuit diagram.The input was given to the resistor with a capacitor shorted to the ground and the output was taken across the capacitor.By this way you can convert a Square wave into sine wave.
COMMUNICATION LINK:
A communication link must be established between modulator and demodulator and here we are using a the efficient IR transmission link which is simple and effective to implement.In this IR LED was used to send the FSK signal when the signal was passed through it emits IR signals and in the detector part Phototransistor was used.The working of the phototransitor was very similar to normal trsnsistor.The infra red signals from the LED falls on the base of the phototransistor and this makes the transistor ON and conducts the signal through the emitter.By this way every IR link wa established we can see this kind of links in remote control appliances.
DEMODULATOR:
The demodulator was constructed in means to correctly match the modulator circuit of this wireless modem.The PLL 565 IC locks the input frequency and tracks it between the two possible frequencies with a DC shift at its output.Then a three stage RC filter was used in the circuit to remove the total sum frequency component.The output will be obtained in this way whenever the input frequency was low that is 1070 Hz then the final output will be moved to logic 1 high state and logic 0 low state when the input frequency was high that is 1270 Hz.For detailed description on the above circuit visitFSK DEMODULATOR USING PLL 565.
RamSrinivassan, This design for wireless data modem is meant only for short distance transmission, Not the data modem you use for internet connectivity.If you want to establish wireless communication between two devices provided that these two will be in short range, you can use the above design.
sir, i have tried to make this one.and i have faced some problems.the ir led is not working.when i connected 555 output to the cro the fsk signal seems to be too identical for both logic 1 and 0.is that due to low frequency of input.what would be the suitable vpp for the input? thank you
Mujeeb, IR led is not working?why?555 will source enough current to drive an IR led.The output of 555 swings between 1270 Hz and 1070 Hz it might not be noticeable enough so try calculating individual frequency values for each state.The PNP transistor acts just as a switch for the input, like 5V will be fine.
Great info.Appreciate it regarding providing us all this type of useful info.Sustain the favorable perform and also carry on providing us all a lot more excellent info every once in awhile.If possible, while you obtain skills, does one thoughts changing your site with additional informationWireless Modems
Above Circuits are tested in simulation and will work fine practically.But the speed of transmission will be very less, so it will be a great to do one for study purpose or transmission of bits between different circuits
你好：）。I am from Netherlands and i don't know how can i disable my signature?Regards
Belleapoks,
Sorry I couldn't understand what you mean.
please help me.hoe to create the wireless data modem.
RamSrinivassan,
This design for wireless data modem is meant only for short distance transmission, Not the data modem you use for internet connectivity.If you want to establish wireless communication between two devices provided that these two will be in short range, you can use the above design.
sir,
i have tried to make this one.and i have faced some problems.the ir led is not working.when i connected 555 output to the cro the fsk signal seems to be too identical for both logic 1 and 0.is that due to low frequency of input.what would be the suitable vpp for the input?
thank you
Mujeeb,
IR led is not working?why?555 will source enough current to drive an IR led.The output of 555 swings between 1270 Hz and 1070 Hz it might not be noticeable enough so try calculating individual frequency values for each state.The PNP transistor acts just as a switch for the input, like 5V will be fine.
usefull info, can i use a kind of communication radio such as handie talkie for the communication link?thaks
Nurkholish,
Of course you can, this circuit will be very cool with such comm link.
how can we test this modem finally after making it
Mujeeb,
Simple testing can be done by connecting a LED to the output.LED on indicates data "1" and LED off indicates data "0"
Great info.Appreciate it regarding providing us all this type of useful info.Sustain the favorable perform and also carry on providing us all a lot more excellent info every once in awhile.If possible, while you obtain skills, does one thoughts changing your site with additional informationWireless Modems
Above Circuits are tested in simulation and will work fine practically.But the speed of transmission will be very less, so it will be a great to do one for study purpose or transmission of bits between different circuits
Is this circuit tested?
Will we get the output easily if we wire the circuit as shown?