Gesture controlled car using Arduino

Who doesn't love playing with RC cars and Robots.Not only playing, engineers and enthusiasts like us love to build and experiment with these stuffs.Also its fair to say that RC's and Robots have became more than just toys, they already have started to integrate into our life slowly.But to take this to another standard we have built a Gesture controlled car using the most powerful development board Arduino.Let's see how to build your own gesture controlled car.

MOTTO OF GESTURE CONTROLLED CAR:

• To drive a toy car using our hand movements or gestures.

HARDWARE USED:

TRANSMITTER PART AND ROBOT:

1. Arduino Uno.
2. ADXL335 accelerometer.
3. 434 MHz RF transmitter.
4. Breadboard.

RECEIVER PART AND ROBOT:

1. Arduino Uno.
2. 434 MHz RF receiver.
3. L293D motor driver IC.
4. Chassis and wheels.
5. 2 DC motors.
6. Breadboard.

SCHEMATIC DIAGRAM OF TRANSMITTER:

ADXL335:

This forms the basic constituent of our gesture controlled car.This basically is an Accelerometer which is capable of detecting acceleration in three axis X,Y and Z.The output of these three axis can be obtained separately from three pins x,y and z.This is shown in the above circuit diagram (I have used only X and Y axis for this project) .Read briefly aboutinterfacing this sensor with Arduino here.

ARDUINO UNO:

The arduino board in the transmitter part acts as an interpreter.This fetches X and Y values from the accelerometer and then decides the gesture.There are five gestures or movements we have used in this project.By trail and error method we have recorded the X and Y values for the gestures, those are

1. Stop or No Movement – X-Value:331  to 339 &  Y-Value:341 to 349
2. Tilt Forward or Forward movement – X-Value:376  to 384 &  Y-Value:336 to 344
3. Tilt Backward or Backward Movement – X-Value:301  to 309 &  Y-Value:351 to 359
4. Tilt Left or Left movement – X-Value:291  to 299 &  Y-Value:276 to 284
5. Tilt Right or Right movement –  X-Value:316  to 324 &  Y-Value:386 to 394

Based on the above conditions the Arduino will decide the movement and send it to transmitter.

433MHZ TRANSMITTER:

This is one of the popular plug and play RF module which comes with a RX pair.It transmits the command received from Arduino and transmit it to rx module at a frequency of 433Mhz.

COMPLETE SETUP OF TRANSMITTER PART:

CODE FOR TRANSMITTER ARDUINO:

//Connect the Transmitter data pin to Arduino pin 12   int xPin=0;//Connect x pin of adxl335 to pin A0  int yPin=1;//Connect y pin of adxl335 to pin A1      int ledPin=13;//led on pin 13 is ON except when transmitter is parallel to the ground      #include
         
          void setup()   {    vw_setup(2000);//Bits per second    pinMode(ledPin,OUTPUT)!Serial.begin(9600);//Initialise the serial connection debugging  }    void loop()   {    int xval=analogRead(xPin)!int yval=analogRead(yPin)!Serial.print("xval=")!Serial.println(xval)!Serial.print("yval=")!Serial.println(yval)!delay(1000)!//used to display values after 1s delay        Serial.print("\n")!if ((xval>330 && xval<340) && (yval>340 && yval<350)) //stationary or stop(transmitter parallel to ground)    {      digitalWrite(ledPin,LOW)!send("s")!}     else     {       if ((xval>375 && xval<385) && (yval>335 && yval<345)) //forward(transmitter tilted forward)      {        digitalWrite(ledPin,HIGH)!send("f")!}      if ((xval>300 && xval<310) && (yval>350 && yval<360)) //backward(transmitter tilted backward)      {        digitalWrite(ledPin,HIGH)!send("a")!}      if ((xval>290 && xval<300) && (yval>275 && yval<285)) //left(transmitter tilted to left)      {        digitalWrite(ledPin,HIGH)!send("l")!}       if ((xval>315 && xval<325) && (yval>385 && yval<395))//right(transmitter tilted to right)      {        digitalWrite(ledPin,HIGH)!send("r")!}    }    delay(1000)!}      void send(char *message)//send function definition  {    vw_send((uint8_t *)message, strlen(message))!vw_wait_tx()!// Wait until the whole message is gone  }
         

SCHEMATIC DIAGRAM OF RECEIVER:

RF RECEIVER:

This is a matching pair of TX used in the transmitter part o this project.On receiving the bytes from Transmitter it sends the data to Arduino for further procesesing.

ARDUINO:

The data from the Receiver is used for interpretation of movements.Once interpretations Arduino commands the motor to move in appropriate directions, There are five possibility of data values from the receiver and each data is interpreted as follows.

1. Character ‘s' or 0x73 – Stop
2. Character ‘f' or 0x66 – Forward
3. Character ‘a' or 0x61 – Backward
4. Character ‘l' or 0x6C – Left
5. Character ‘r' or 0x72 – Right

Once the interpretations are made Arduino operates the motor accordingly.

L293D & MOTORS:

L293D is a motor driver IC which is used since Arduino cannnot provide enough current to drive a motor.Two motors are used to take care of all the movements ( Forward, Backward, Left and Right)

COMPLETE SETUP OF RECEIVER AND CAR:

CODE FOR RECEIVER PART:

//Connect the Receiver data pin to Arduino pin 11    #include
         
          byte message[VW_MAX_MESSAGE_LEN]!// a buffer to store the incoming messages  byte messageLength = VW_MAX_MESSAGE_LEN!// the size of the message  int lm=12;//pin 12 of arduino to pin 9  of ic  int lmr=8;//pin 8 of arduino to pin 2 of ic    int rm=10;//pin 10 of arduino to pin 10 of ic    int rmr=7;//pin 7 of arduino to pin 15 of ic  int ledPin=13;//led on pin 13 is ON except when bot is stationary    void setup()  {   Serial.begin(9600);//Initialise the serial connection debugging     pinMode(ledPin,OUTPUT)!pinMode(lm,OUTPUT)!pinMode(lmr,OUTPUT)!pinMode(rm,OUTPUT)!pinMode(rmr,OUTPUT)!vw_setup(2000)!// Bits per sec   vw_rx_start()!// Start the receiver  }  void loop()  {      uint8_t buf[VW_MAX_MESSAGE_LEN]!uint8_t buflen = VW_MAX_MESSAGE_LEN!if (vw_get_message(buf, &buflen)) // Non-blocking      {     int i!Serial.print("Got: ");//debugging          for (i = 0!i < buflen!i++)     {        // Serial.print(buf[i],HEX);//You may also use integer values debugging         //Serial.print(' ');// debugging              if (buf[i]==0x73)//Stationary            {              digitalWrite(lm,LOW)!digitalWrite(lmr,LOW)!digitalWrite(rm,LOW)!digitalWrite(rmr,LOW)!digitalWrite(ledPin,LOW)!}            else            {              if(buf[i]==0x66)//Forward              {                digitalWrite(lm,LOW)!digitalWrite(lmr,HIGH)!digitalWrite(rm,HIGH)!digitalWrite(rmr,LOW)!digitalWrite(ledPin,HIGH)!}                          if (buf[i]==0x61)//Backward              {                digitalWrite(lm,HIGH)!digitalWrite(lmr,LOW)!digitalWrite(rm,LOW)!digitalWrite(rmr,HIGH)!digitalWrite(ledPin,HIGH)!}                          if (buf[i]==0x6C)//Left               {                digitalWrite(lm,LOW)!digitalWrite(lmr,LOW)!digitalWrite(rm,HIGH)!digitalWrite(rmr,LOW)!digitalWrite(ledPin,HIGH)!}                          if (buf[i]==0x72)//Right               {                digitalWrite(lm,LOW)!digitalWrite(lmr,HIGH)!digitalWrite(rm,LOW)!digitalWrite(rmr,LOW)!digitalWrite(ledPin,HIGH)!}             }          }       //Serial.print("\n");// debugging          }          //delay(1000)  }
         

WORKING VIDEO:

APPLICATIONS:

1. Gesture controlled car or Robots can be used in military and tactical units to save lives.
2. Medical applications due to its precision.
3. Construction and heavy machinery.

MAKERS:

1. Navatha
2. Anusha
3. Tejaswini